Datalogic POWERSCAN PD7100 Specifikace Strana 105
- Strana / 392
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Product Reference Guide 95
Chapter 10
Wand Emulation Interface
Introduction
This chapter provides feature/settings configuration for the Wand Emulation interface.
Wand Emulation Standard Factory Settings
Reference Appendix B, Standard Defaults for a listing of standard factory settings.
Wand Idle State
This feature specifies the level of the Wand output signal when the reader is idle.
NOTE
TTL logic levels:
0V <= Low <= 0.7V
2.4V <= High <= 5.25V
ENTER/EXIT PROGRAMMING MODE
Wand Idle State = Low
Wand Idle State = High
DEFAULT
- PowerScan 1
- Product Reference Guide 1
- Table of Contents 3
- 2PowerScan 4
- 6PowerScan 8
- 8PowerScan 10
- PD7100 Corded 10
- Chapter 1 11
- Introduction 11
- Manual Conventions 12
- References 12
- Technical Support 13
- 4PowerScan 14
- Chapter 2 15
- Getting Started 15
- Setting Up the Reader 16
- Programming 17
- Select the Interface Type 18
- Configure Interface Settings 18
- Configure Other Features 18
- Software Version Transmission 19
- 10 PowerScan 20
- Chapter 3 21
- Interfaces 21
- 12 PowerScan 22
- 13 23
- 14 PowerScan 24
- Global Interface Features 25
- USB Suspend Mode 26
- Chapter 4 27
- General Features 27
- 18 PowerScan 28
- Label Gone Timeout 29
- Label Gone Timeout — cont 30
- Sleep Mode Timeout 31
- 22 PowerScan 32
- LED and Beeper Indicators 33
- Good Read: When to Indicate 34
- Good Read Beep Type 35
- Good Read Beep Frequency 36
- Good Read Beep Length 36
- 27 37
- Good Read Beep Volume 38
- Good Read LED Duration 39
- 30 PowerScan 40
- 2 seconds 40
- Scanning Features 41
- Scan Mode — continued 42
- Stand Mode Triggered Timeout 43
- 34 PowerScan 44
- Scanning Active Time 45
- Scanning Active Time — cont 46
- Flash On Time 47
- Flash On Time — cont 48
- Flash Off Time 49
- Flash Off Time — cont 50
- Stand Mode Sensitivity 51
- Laser Pointer Control 52
- Laser Pointer Period 53
- Green Spot Duration 54
- Chapter 5 55
- RS-232 ONLY Interface 55
- Baud Rate — continued 56
- Data Bits 57
- Stop Bits 58
- Parity = None 59
- Parity = Even 59
- Parity = Odd 59
- Handshaking Control 60
- Chapter 6 61
- RS-232/USB-Com Interfaces 61
- Intercharacter Delay 62
- Intercharacter Delay — cont 63
- Beep On ASCII BEL 64
- Beep On Not on File 64
- ACK NAK Options 65
- ACK Character 66
- ACK Character — cont 67
- NAK Character 68
- NAK Character — cont 69
- ACK NAK Timeout Value 70
- ACK NAK Timeout Value — cont 71
- ACK NAK Retry Count 72
- ACK NAK Retry Count — cont 73
- ACK NAK Error Handling 74
- Indicate Transmission Failure 75
- Disable Character 76
- Disable Character — cont 77
- Enable Character 78
- Enable Character — cont 79
- 70 PowerScan 80
- Chapter 7 81
- Keyboard Interface 81
- Country Mode 82
- Country Mode — continued 83
- Caps Lock State 85
- Send Control Characters 86
- Wedge Quiet Interval 87
- Wedge Quiet Interval — cont 88
- Intercode Delay 91
- Intercode Delay — cont 92
- USB Keyboard Speed 93
- 84 PowerScan 94
- Chapter 8 95
- USB-OEM Interface 95
- USB-OEM Device Usage 96
- USB-OEM Interface Options 97
- 88 PowerScan 98
- Chapter 9 99
- IBM 46XX Interface 99
- 46xx Number of Host Resets 100
- 91 101
- 92 PowerScan 102
- ENTER/EXIT PROGRAMMING MODE 103
- IBM Standard Format — 103
- Code 39 Format — 103
- IBM 46XX Interface Options 104
- Chapter 10 105
- Wand Emulation Interface 105
- Wand Polarity 106
- Wand Signal Speed 107
- Label Symbology Conversion 108
- Transmit Noise 109
- 100 PowerScan 110
- Chapter 11 111
- Data Editing 111
- Please Keep In Mind 112
- Global Prefix/Suffix 112
- Appendix E, Key 113
- Global AIM ID 114
- Global AIM ID — continued 115
- GS1-128 AIM ID 116
- Label ID 117
- 108 PowerScan 118
- 109 119
- Label ID — continued 121
- Case Conversion 131
- Character Conversion 131
- 0xFFFFFFFFFFFFFFFF 132
- (No character conversion) 132
- Chapter 12 133
- Symbologies 133
- Disable All Symbologies 134
- Coupon Control 135
- UPC-A Enable/Disable 136
- UPC-A — cont 137
- UPC-E Enable/Disable 139
- UPC-E — cont 140
- GTIN Formatting 143
- EAN 13 Enable/Disable 144
- EAN 13 — cont 145
- EAN-13 ISBN Conversion 146
- ISSN Enable/Disable 146
- EAN 8 Enable/Disable 148
- EAN 8 — cont 149
- UPC/EAN Global Settings 151
- 142 PowerScan 152
- UPC/EAN Correlation 153
- UPC/EAN Reconstruction 153
- UPC/EAN Price Weight Check 154
- UPC-A Minimum Reads 155
- Optional Add-ons 156
- Add-Ons — cont 157
- GS1 DataBar 167
- Omnidirectional 167
- Omnidirectional — cont 168
- Expanded 169
- Expanded — cont 170
- Limited 176
- Limited — cont 177
- Code 39 Enable/Disable 178
- Code 39 — cont 179
- Code 39 Stitching 194
- Code 32 Enable/Disable 195
- 186 PowerScan 196
- Code 128 197
- Code 128 — cont 198
- GS1-128 Enable 211
- Interleaved 2 of 5 (I 2 of 5) 212
- 203 213
- 204 PowerScan 214
- I 2 of 5 Minimum Reads 215
- 2 of 5 Decoding Level 216
- 2 of 5 Decoding Level — cont 217
- I 2 of 5 Length Control 218
- I 2 of 5 Set Length 1 219
- 06 = Length 1 is 6 Characters 220
- 210 PowerScan 220
- I 2 of 5 Set Length 2 221
- I 2 of 5 Set Length 2 — cont 222
- 213 223
- I 2 of 5 Stitching 224
- Interleaved 2 of 5 CIP HR 225
- Datalogic 2 of 5 225
- Datalogic 2 of 5 — cont 226
- 224 PowerScan 234
- Codabar Enable/Disable 237
- Codabar — cont 238
- Codabar Stitching 254
- ABC Codabar 255
- ABC Codabar — cont 256
- Code 11 Enable/Disable 258
- Code 11 — cont 259
- Code 11 Decoding Level 269
- Code 11 Stitching 272
- Standard 2 of 5 273
- Standard 2 of 5 — cont 274
- Standard 2 of 5 Stitching 282
- Industrial 2 of 5 283
- Industrial 2 of 5 — cont 284
- IATA Enable/Disable 292
- ISBT 128 293
- ISBT 128 — cont 294
- 285 295
- MSI Enable/Disable 297
- MSI — cont 298
- MSI Decoding Level — cont 306
- Plessey Enable/Disable 307
- Plessey — cont 308
- Code 93 — cont 318
- Codablock F 329
- Codablock F — cont 330
- Code 4 Enable/Disable 336
- Code 4 — cont 337
- Code 5 Enable/Disable 338
- Code 5 — cont 339
- Code 4 and 5 Decoding Level 340
- 331 341
- 332 PowerScan 342
- Follett 2 of 5 343
- 334 PowerScan 344
- Appendix A 345
- 336 PowerScan 346
- Standard Cable Pinouts 347
- 338 PowerScan 348
- Appendix B 349
- 340 PowerScan 350
- 341 351
- 343 353
- GS1 DataBar Omnidirectional 353
- GS1 DataBar Expanded 353
- GS1 DataBar Limited 353
- 344 PowerScan 354
- 346 PowerScan 356
- 347 357
- 348 PowerScan 358
- Default Exceptions 360
- 351 361
- Interface: RS232-OPOS 361
- 352 PowerScan 362
- Appendix C 363
- LED and Beeper Indications 364
- Error Codes 365
- 356 PowerScan 366
- Appendix D 367
- Sample Barcodes — continued 368
- Code 32 368
- Codabar 368
- Code 93 368
- Code 11 368
- GS1 DataBar (RSS) 369
- 360 PowerScan 370
- Appendix E 371
- 362 PowerScan 372
- 363 373
- 364 PowerScan 374
- Appendix F 375
- Product Reference Guide 366 376
- Product Reference Guide 367 377
- Product Reference Guide 368 378
- Product Reference Guide 369 379
- Digital Interface 380
- Digital Interface — cont 381
- IBM31xx 102-key 382
- IBM31xx 102-key — cont 383
- IBM XT — cont 385
- 376 PowerScan 386
- 377 387
- 378 PowerScan 388
- ASCII Character Set 391
- Datalogic ADC, Inc 392
Související produkty a manuály pro Čtečky čárových kódů Datalogic POWERSCAN PD7100
(2 stránky)
Čtečky čárových kódů Datalogic QLM700 Instalační manuál
(120 stránky)
(120 stránky)
(20 stránky)
(2 stránky)
Čtečky čárových kódů Datalogic GryphonD432 Specifikace
(160 stránky)
(160 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.085 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce