Datalogic AL5010 Technické informace Strana 44
- Strana / 240
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
36 Mechanical Installation AccuLazr
™
AL5010 Product Line Manuals
To install your optional I/O module(s):
1. Remove the cover to gain access to the printed circuit board.
2. The I/O modules may be plugged into locations I/O 1 through I/O 4.
These locations run left-to-right, as shown on the circuit board
silkscreen.
3. Plug the appropriate I/O module directly into the interface module’s
circuit board.
4. Using a screwdriver, secure the I/O module by tightening the captive
screw (that goes through the module) into the circuit board. DO NOT
over-tighten screw.
Installing an I/O Module
Accu-Sort Systems, Inc. 03-AL5010_Mechanical_Installation_R20.doc
- Product Line Manual 1
- Contents 3
- Preface 3
- 1 Introduction 3
- 3 Mechanical Installation 3
- 4 Electrical Installation 4
- 5 Setup 4
- 6 Operations 4
- D Networking Guide 6
- F Installation Drawings 6
- -'37%"3) 7
- Conventions 8
- Customer Service 8
- AL5010 Scan Head 10
- AL5010 Mounting Base 10
- AccuLazr Interface Module 11
- AccuLazr 12
- User Interface 12
- Options and Accessories 14
- 2 Safety 15
- General Precautions 16
- Compliance Requirements 17
- Electrical Safety 17
- Electrostatic Discharge 18
- Basic Rules for ESD Control 18
- Laser Safety 19
- Safety Labels and Locations 20
- 0HFKDQLFDO,QVWDOODWLRQ 21
- Unpacking Instructions 22
- Installation Sequence 23
- Orientation Considerations 24
- Read Range 24
- ← DIRECTION OF TRAVEL → 25
- General Mounting Guidelines 26
- Raster Setup 28
- AL5010 Product Line Manuals 30
- Dimensions and Clearances 35
- Attaching the Mounting Base 35
- Mounting the Tachometer 39
- Mounting the I/O Modules 43
- -'3'3A#191039) 45
- @..59);3A#1'3/))) 45
- !//101.2%5)82B.'C%01.2) 45
- Installation Sequence(s) 46
- Installing Multiple Readers 47
- Basic Interface Module 50
- Enhanced Interface Module 52
- Electrical wiring sequence: 53
- Power Requirements 54
- Trigger Connections 55
- Tachometer Connections 56
- I/O Module Connections 59
- DeviceNet 61
- Profibus 61
- Connecting the AL5010 61
- AL5010 Pin-Out Table 62
- Check Installation 63
- Getting Help 67
- Modify Settings 68
- Settings > Configuration 69
- Settings > Bar Codes 70
- Settings > Modulo Checks 73
- Settings > Match Codes 75
- Settings > Network 79
- Settings > Trigger 82
- Settings > Relay 83
- Settings > Tracking 84
- Settings > Advanced 86
- Settings > Raster 88
- Diagnostics 90
- Diagnostics > Monitor 91
- Diagnostics > Log Viewer 92
- Error Counters 95
- First-time Setup 100
- Operations Checklist 101
- Control Panel Indicators 102
- Backup / Restore Procedures 107
- Standalone Operation 110
- Tracking Operation 111
- Dual X-Scanning Operation 112
- 7 Maintenance 115
- Maintenance Tasks 116
- Cleaning the Exit Window 117
- Cleaning the Tachometer 119
- Tighten Mounting Hardware 119
- Verify Reader Operation 120
- Verify Photoeye Operation 120
- Verify Tachometer Operation 120
- 8 Troubleshooting 121
- (Laser Shutoff) 123
- Monitor 125
- Status LEDs 126
- Read Quality 127
- Log Viewer 128
- Decode/DSP Counters 132
- Update Firmware 133
- Troubleshooting 134
- Discovering the IP Address 136
- !!52&60!2( 137
- AL5010 Interface Module 139
- Other FRUs 139
- Specifications 141
- Power Supply for AL5010 143
- Output Modules 143
- Input Module 143
- Certifications 144
- Read Charts 145
- Combo Read Chart / Table 146
- ™ User Interface AccuLazr 158
- ™ User Interface 151 159
- ™ User Interface 153 161
- ™ User Interface 155 163
- ™ User Interface 157 165
- ™ User Interface 159 167
- ™ User Interface 161 169
- ™ User Interface 163 171
- ™ User Interface 165 173
- ™ User Interface 167 175
- ™ User Interface 169 177
- ™ User Interface 171 179
- ™ User Interface 173 181
- ™ User Interface 175 183
- ™ User Interface 177 185
- ™ User Interface 179 187
- ™ User Interface 181 189
- ™ User Interface 183 191
- ™ User Interface 185 193
- AL5010 Networking Guide 195
- Configuration 196
- Restrictions 197
- TCP/IP Server 198
- TCP/IP Client 199
- UDP Messaging 199
- EtherNet/IP 200
- EtherNet/IP Options 201
- Explicit Messaging Example 202
- I/O Messaging Example 203
- AL5010:C Configuration Data 205
- AL5010:I Input Data 205
- AL5010:O Output Data 205
- EtherNet/IP Object Models 208
- Glossary 208
- Summary of Objects 208
- Definitions 208
- Assembly Object (04 210
- – 4 Instances) 210
- FAST Monitor Configuration 215
- Installation Drawings 217
- 217
- AL5010 Product Line Manual 218
- SOLIDWORKS 219
- ASSEMBLED VIEW 229
- 3ECO 12-40 230
- JG 02/14/12 230
- FIELDBUS 234
- 1 2 3 4 5 235
- 1 INITIAL RELEASE 235
- NRS 11/23/10 235
Související produkty a manuály pro Čtečky čárových kódů Datalogic AL5010
(28 stránky)
(10 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce