Datalogic Dragon D131 Specifikace Strana 176
- Strana / 210
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
DRAGON™ D131/M131
166
5.14.2 Copy Dragon™ M131 Series
Procedure
:
Using the slave reader and its OM-30X0 cradle, follow the initialization
procedure in chapter 4 of this manual or from the Quick Reference Manual.
With the master Dragon™ M131 (correctly configured reader), read the Copy
Configuration barcode below. Then place it onto an OM-30X0 cradle within 10
seconds. The reader will beep indicating the configuration has been copied.
The configuration will be simultaneously sent over the RS232 interface of the
OM-30X0. If this causes undesired effects disconnect the RS232 cable between
the PC and OM-30X0 during this process.
Copy Configuration
Ì$+ZZ0$-*Î
With the slave Dragon™ M131, read the Get Configuration barcode below.
Then place it onto the same OM-30X0 cradle used in the step above. The slave
reader's address will not be changed.
Get Configuration
Ì$+ZZ2$-4Î
The configuration will be copied from the master to the slave Dragon™ M131. The
slave Dragon™ M131 signals the end of the procedure with a series of beeps. It is
now ready to be used with its own OM-30X0 cradle.
Repeat the procedure above to configure other slave readers. The
OM-30X0 can continue to configure slave readers until it receives another
command or data.
- Dragon™ D131/M131 1
- Reference Manual 1
- CONTENTS 3
- GENERAL VIEW 9
- 1 INTRODUCTION 11
- 2 INSTALLATION 12
- INSTALLATION 13
- CAUTION 13
- 2.3 RS232 CONNECTION 15
- 2.4 USB 15
- 2.5 IBM USB POS 16
- 2.6 WEDGE CONNECTION 17
- 2.7 PEN EMULATION CONNECTION 17
- 2.8 NETWORK CONNECTIONS 18
- 2.8.2 Network Cabling 19
- 2.8.3 Network Termination 20
- 2.9.1 Battery Charging 21
- 2.10.1 Desktop mounting 23
- Portable Desktop Use 24
- Fixed Desktop Use 24
- 2.10.2 Wall Mounting 26
- Inclined Base Wall-mounting 27
- LAYOUTS 28
- 3.1.4 C-BOX Layout 30
- 3.2.1 Host Master Layout 31
- 3.2.2 OM-3000 Master Layout 32
- /*32: FAIL*/ 33
- 4 CONFIGURATION 34
- 4.2 SETUP PROCEDURES 35
- Ì$+$*oÎ 36
- ÌIB'Î 37
- ÌRA0RFHÎ 38
- Ì$+RN0$-IÎ 38
- Ì$+RX0$-qÎ 39
- Ì$+RN1$-NÎ 39
- END of procedure 40
- Ì$+RF4Î 43
- Ì$+RZ2$-ÇÎ 44
- Ì$+RZ1$-~Î 44
- Ì$+CP0$-$Î 45
- Ì$+CM2EC0$->Î 45
- Ì$+CM1$-ÈÎ 45
- Ì$+CM0$-ÃÎ 45
- Ì$+CP6$-BÎ 45
- Ì$+CP512$-uÎ 48
- Ì$+CP513$- 48
- First Start-Up 49
- CONFIGURATION 51
- RS232 PARAMETERS 52
- BAUD RATE 53
- DATA BITS 54
- STOP BITS 54
- HANDSHAKING 54
- ACK/NACK PROTOCOL 55
- INTER-CHARACTER DELAY 55
- RX TIMEOUT 56
- SERIAL TRIGGER LOCK 56
- USB PARAMETERS 57
- USB-COM 58
- USB-KBD 60
- KEYBOARD NATIONALITY 60
- INTER-CODE DELAY 62
- USB KEYBOARD SPEED 62
- WEDGE PARAMETERS 63
- CAPS LOCK 65
- NUM LOCK 66
- KEYBOARD SETTING 67
- CONTROL CHARACTER EMULATION 69
- PEN EMULATION 70
- OPERATING MODE 71
- MINIMUM OUTPUT PULSE 72
- OVERFLOW 73
- OUTPUT LEVEL 74
- IDLE LEVEL 74
- INTER-BLOCK DELAY 74
- NETWORK PARAMETERS 75
- RS485 NETWORK 76
- NETWORK BAUD RATE 76
- SLAVE ADDRESS RANGE 77
- NETWORK WARNING MESSAGE 77
- RECEPTION WARNING MESSAGE 77
- MASTER CRADLE HEADER 78
- MASTER CRADLE TERMINATOR 79
- DATA FORMAT 80
- CODE IDENTIFIER 82
- CUSTOM CODE IDENTIFIER 82
- TERMINATOR 84
- SPECIAL KEYS 85
- FIELD ADJUSTMENT 86
- FIELD ADJUSTMENT CHARACTER 87
- CODE LENGTH TX 87
- CHARACTER REPLACEMENT 88
- POWER SAVE 92
- SLEEP STATE 93
- ENTER SLEEP TIMEOUT 93
- READING PARAMETERS 94
- TRIGGER TYPE 95
- TRIGGER SIGNAL 95
- TRIGGER CLICK 95
- TRIGGER-OFF TIMEOUT 96
- FLASH MODE 96
- READS PER CYCLE 96
- SAFETY TIME 97
- BEEPER INTENSITY 97
- BEEPER TONE 98
- BEEPER TYPE 98
- BEEPER LENGTH 98
- GOOD READ SPOT DURATION 99
- AIMING SYSTEM 99
- CRADLE BEEPER INTENSITY 99
- DECODING PARAMETERS 100
- INK SPREAD 101
- OVERFLOW CONTROL 101
- INTERDIGIT CONTROL 101
- DECODING SAFETY 102
- PUZZLE SOLVER™ 102
- CODE SELECTION 103
- Ì#+AUTOWÎ 104
- EAN/UPC FAMILY 106
- 2/5 FAMILY 112
- CODE 39 FAMILY 113
- CODE 128 FAMILY 114
- CODE 93 115
- CODABAR FAMILY 115
- CODE 11 118
- CODE 16K 119
- CODE 49 119
- RSS CODES 120
- ADVANCED FORMATTING 121
- CONCATENATION 122
- RADIO PARAMETERS 140
- RADIO PROTOCOL TIMEOUT 141
- POWER-OFF TIMEOUT 141
- TRANSMISSION MODE 142
- SINGLE STORE 143
- BATCH MODE 144
- FIND ME 144
- DISPLAY PARAMETERS 145
- DATE AND TIME 146
- CONTRAST 146
- FONT SIZE 146
- BACKLIGHT 146
- DISPLAY-OFF TIMEOUT 147
- DISPLAY MODE 147
- 5 REFERENCES 149
- 5.1.2 ACK/NACK Protocol 150
- 5.1.3 FIFO 151
- 5.1.4 RX Timeout 152
- 5.2 PEN PARAMETERS 152
- 5.2.1 Minimum Output Pulse 152
- 5.2.3 Overflow 153
- 5.2.5 Inter-Block Delay 154
- 5.3 NETWORK PARAMETERS 154
- 5.4 DATA FORMAT 155
- Enter Configuration 157
- DRAGON™ D131/M131 160
- ÌFQ9C2>Î 162
- 5.4.3 Address Stamping 164
- 5.4.4 Address Delimiter 164
- 5.4.5 Time Stamping Format 165
- 5.5 POWER SAVE 165
- 5.5.1 Sleep State 165
- 5.6.5 Safety Time 167
- 5.7 DECODING PARAMETERS 167
- 5.7.1 Ink-Spread 167
- 5.7.2 Overflow Control 167
- 5.7.3 Interdigit Control 168
- 5.8 ADVANCED FORMATTING 168
- 5.8.1 Match Conditions 168
- 5.9.2 Power-Off Timeout 169
- 5.9.3 Transmission Mode 169
- 5.9.5 Single Store 170
- 5.9.6 Batch Mode 171
- 5.10.1 Display Mode 172
- Ì$+$0ÂÎ 174
- Ì$+$1$Î 174
- Ì#+CODEÂÎ 174
- Ì$+ZZ0$-*Î 175
- Ì$+ZZ2$-4Î 176
- Ì$+ZZ3$-9Î 177
- Ì$+RN2$-SÎ 179
- 6 MESSAGE FORMATTING 180
- 6.1.1 Cursor Control 181
- 6.1.2 Font Selection 182
- 6.1.3 Clearing Display 182
- 6.1.5 Setting RTC 183
- 7 TECHNICAL FEATURES 185
- 7.2 DRAGON™ M131 186
- 7.3 OM-30X0 / C-3000 187
- 7.5 STATUS INDICATORS 188
- 7.6 READING DIAGRAMS 191
- AC410132BH0 192
- SERIAL CONFIGURATION STRINGS 193
- (not for USB-KBD-ALT-MODE) 195
- (IBM AT compatible only) 195
- (only for D131 series) 200
- B CODE IDENTIFIER TABLE 206
- C HEX AND NUMERIC TABLE 209
Související produkty a manuály pro Čtečky čárových kódů Datalogic Dragon D131
(2 stránky)
Čtečky čárových kódů Datalogic POWERSCAN HD Specifikace
(212 stránky)
(212 stránky)
(15 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce