Datalogic Magellan 1100i Manuál s instrukcemi Strana 23
- Strana / 208
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
LED and Beeper Indicators
Product Reference Guide
15
Good Read: When to Indicate
This feature specifies when the scanner will provide indication (beep and/or flash its green
LED) upon successfully reading a barcode. Choices are:
• Good Read = Indicate after decode
• Good Read = Indicate after transmit
• Good Read = Indicate after CTS goes inactive, then activ
NOTE
This option (Indicate after CTS goes inactive,
t
hen active), which uses CTS, is only valid for
RS-232 interfaces.
e
START / END
PROGRAMMING BARCODES
After Decode
DEFAULT
³
After Transmit
After CTS goes inactive, then active
- Magellan 1
- Table of Contents 3
- Product Reference Guide iii 5
- Getting Started 9
- Connecting the Scanner 10
- Programming 11
- LED and Beeper Indicators 12
- Error Codes 13
- General Features 15
- Aztec or Composite label 17
- Label Gone Timeout 18
- Sleep Mode 19
- Sleep Mode — cont 20
- ERI Timeout 22
- Good Read: When to Indicate 23
- Good Read Beep Control 24
- Good Read Beep Frequency 24
- Good Read Beep Length 25
- Good Read Beep Volume 26
- Green Spot 26
- Aiming Pointer Settings 27
- Scanning Features 28
- Target Mode Linger Time 29
- Wake Up Intensity 30
- Image Capture 31
- Image Compression 32
- Image Size 32
- Image Brightness 33
- Image Contrast 33
- Cell Phone Mode 34
- Cell Phone in Target Mode 37
- Interface Related Features 39
- Mappings 40
- Interface Selection 41
- Interface Selection — cont 42
- Interface Features 43
- Interface Features — cont 44
- RS-232 Interface Features 45
- Hardware Flow Control 47
- Intercharacter Delay 48
- Intercharacter Delay — cont 49
- Software Flow Control 49
- Host Echo Quiet Interval 50
- Signal Voltage: Normal/TTL 51
- Beep on ASCII BEL 52
- Beep on Not on File 52
- ACK NAK Options 53
- ACK Character 54
- NAK Character 54
- Retry on ACK NAK Timeout 55
- ACK NAK Timeout Value 55
- ACK NAK Retry Count 56
- ACK NAK Error Handling 57
- USB-OEM Interface Features 58
- USB Keyboard 60
- Keyboard Wedge — cont 61
- USB COM Interface Set-up 66
- Data Editing 67
- Global Prefix/Suffix 68
- Global Prefix/Suffix — cont 69
- Label ID 71
- Label ID — cont 72
- Case Conversion 78
- Character Conversion 79
- UPC-A — continued 82
- Disable/Enable UPC-E 85
- Check Digit Transmission 85
- UPC-E — continued 86
- Expand UPC/EAN to GTIN 88
- Disable/Enable EAN-13 89
- EAN-13 — continued 90
- Disable/Enable EAN-8 92
- EAN-8 — continued 93
- EAN Two-Label 94
- EAN Two-Label — continued 95
- Price Weight Check Digit 100
- Contact Customer Support for 101
- Add-ons — continued 102
- UCC/EAN 128 Emulation 105
- Minimum Reads 106
- GS1-128 Emulation 107
- Length Control 108
- Coupon Read Control 111
- GS1 DataBar Limited 112
- Disable/Enable Code 39 114
- Check Character Calculation 114
- Check Character Transmit 115
- Start/Stop Characters 115
- Code 39 Full ASCII 116
- Code 39 — continued 117
- Quiet Zones 118
- Code 32 Italian Pharmacode 120
- Code 128 122
- Code 128 — continued 123
- Interleaved 2 of 5 127
- Check Digit Transmit 128
- Symbologies 130
- Interleaved 2 of 5 Stitching 131
- Disable/Enable Codabar 133
- Check Character Verification 133
- Codabar — continued 135
- Start/Stop Character Match 138
- Codabar Stitching 138
- Disable/Enable Code 93 140
- Code 93 — continued 141
- MSI/Plessey 144
- MSI/Plessey — continued 145
- Standard 2 of 5 150
- Standard 2 of 5 — continued 151
- 2D Symbologies 157
- Disable/Enable PDF 417 158
- PDF 417 — continued 159
- Micro PDF 417 161
- Micro PDF 417 — continued 162
- Datamatrix 164
- Datamatrix — continued 165
- Disable/Enable QR Code 167
- QR Code — continued 168
- Maxicode 170
- Maxicode — continued 171
- Disable/Enable Aztec 173
- Aztec — continued 174
- Composite Labels 176
- Advanced Decoding Features 179
- Inverse Label Reading 180
- Chapter A 181
- Product Specifications 181
- Physical Properties 182
- Electrical Parameters 182
- Environmental Parameters 182
- Other Parameters 182
- Cable Pinouts 183
- USB, USB Keyboard 184
- & USB COM 184
- Keyboard Wedge 184
- Alpha-Numeric Pad 185
- Appendix D 187
- Default Settings 187
- Interface Default Exceptions 188
- RS-232 Wincor/Nixdorf 189
- Keyboards 190
- Appendix E 191
- Chapter F 199
- Host Commands 199
- Chapter G 201
- Sample Symbols 201
- 1D Symbol Samples — continued 202
- 2D Sample Symbols 203
- Composite Sample Symbols 204
- 197 205
- ASCII Chart 207
- Datalogic ADC, Inc 208
Související produkty a manuály pro Čtečky čárových kódů Datalogic Magellan 1100i
(2 stránky)
(50 stránky)
Čtečky čárových kódů Datalogic DS4800 Uživatelský manuál
(100 stránky)
(100 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce