Datalogic QLM500 Manuál s instrukcemi Strana 38
- Strana / 161
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
MATRIX 410™ REFERENCE MANUAL
28
2
7. Configure the other device parameters via VisiSet™ [Operating Mode, Calibration, Data
Collection parameters, etc.].
8. The Slave device is now Configured. Physically connect it to the Master/Slave network. If
using the CBX connection box equipped with a BM100 Backup module, you can perform
Device Backup at the Slave (see par. 2.4 for details).
The Slave device is now Configured. Repeat these steps for each Slave reader in the ID-
NET™ network.
Configuration of Master
1. Connect a PC equipped with VisiSet™ to the Main, Auxiliary or Ethernet interface of the
planned Master reader.
2. Launch VisiSet™ and connect to the Master reader.
3. From the VisiSet™ Device Menu select "Parameter Setup".
4. Set the Role of the Master reader (Synchronized or Multidata) from the
Reading System Layout > Device Network Setting > Topology Role parameter.
5. Enable the planned Slave device N from the Reading System Layout >
Expected Slave Device #N > Status parameter and, if desired, set the related
identification string from the Expected Slave Device #N > Device Description parameter.
Repeat this step for all planned Slave devices.
6. If necessary, set the ID-NET™ baudrate from the Reading System Layout >
Device Network Setting > Network Baud Rate parameter, (500 kbs default).
7. Configure the other device parameters via VisiSet™ [Operating Mode, Calibration, Data
Collection parameters, etc.].
8. The Master device is now Configured. Physically connect it to the Master/Slave network.
If using the CBX connection box equipped with a BM100 Backup module, perform a
Network Backup at the Master (see par. 2.4 for details).
9. From the VisiSet™ Device Menu select "ID-NET™ Status Window" and click on the
"Look For Devices On Network" button to check the status of the expected Slave devices
within the ID-NET™ network.
The reader network is ready.
- MATRIX 410™ 1
- CONTENTS 3
- REFERENCES 6
- COMPLIANCE 7
- HANDLING 8
- GENERAL VIEW 10
- 1 RAPID CONFIGURATION 11
- Required Accessories 12
- STEP 2 – CONNECT THE SYSTEM 13
- (polarity insensitive) 14
- RAPID CONFIGURATION 15
- STEP 4 – FOCUS THE READER 16
- Locate Function 17
- STEP 9 – TEST MODE 27
- Host Mode Programming 30
- Alternative Layouts 30
- Code Quality Verification 30
- 2 INTRODUCTION 31
- INTRODUCTION 33
- 2.3 ID-NET™ 36
- VISISET™ 40
- Restore 41
- Replacement 42
- 2.5.1 X-PRESS™ Functions 45
- Test Mode (Function 1) 46
- Focus/Locate (Function 2) 46
- Setup (Function 3) 47
- Learn (Function 4) 47
- 2.5.2 Diagnostic Indication 47
- 2.6 MODEL DESCRIPTION 48
- 2.7 ACCESSORIES 48
- 2.7.1 Lighting System Notes 50
- 2.8 APPLICATION EXAMPLES 51
- 2.8.1 Document Handling 51
- 2.8.4 Direct Part Marking 53
- 3 INSTALLATION 57
- 3.2 MECHANICAL DIMENSIONS 58
- INSTALLATION 59
- [Ø0.32] 60
- Figure 43 - Pitch angle 62
- Figure 44 - Skew angle 62
- Figure 45 - Tilt angle 62
- CBX ELECTRICAL CONNECTIONS 63
- 4.1 POWER SUPPLY 64
- 4.2 MAIN SERIAL INTERFACE 65
- 4.2.1 RS232 Interface 66
- 4.3 ID-NET™ INTERFACE 70
- 4.3.1 ID-NET™ Cables 70
- 4.3.2 ID-NET™ Response Time 71
- 4.5 INPUTS 76
- 5.1 M16 19-PIN CONNECTOR 83
- 5.4.1 RS232 Interface 86
- 5.5 ID-NET™ INTERFACE 90
- 5.5.1 ID-NET™ Cables 90
- 5.5.2 ID-NET™ Response Time 91
- 5.8 INPUTS 97
- EXTERNAL TRIGGER 98
- Matrix 410™ 98
- INPUT DEVICE 99
- 5.9 OUTPUTS 100
- USER INTERFACE 101
- MATRIX 410™ REFERENCE MANUAL 102
- 6 TYPICAL LAYOUTS 103
- 6.2 PASS-THROUGH 106
- 6.2.1 Pass-Through on RS232 106
- 6.3 ID-NET™ 108
- BA600 ID-NET™ Out 109
- BA400 Ext. Power 109
- BA500 Trigger 109
- BA300 Service 109
- Fieldbus Interface 113
- 6.4 RS232 MASTER/SLAVE 114
- 6.5 MULTIPLEXER 115
- 6.6 ETHERNET CONNECTION 116
- TYPICAL LAYOUTS 117
- 7 READING FEATURES 118
- READING FEATURES 119
- 7.2.2 1D (Linear) Codes 120
- Line Speed 125
- 8 SOFTWARE CONFIGURATION 127
- 8.2 INSTALLING VISISET™ 128
- 8.3 STARTUP 128
- 8.3.1 VisiSet™ Options 129
- 8.4 CONFIGURATION 131
- Parameters to verify/modify: 133
- SOFTWARE CONFIGURATION 135
- 8.4.3 Calibration 138
- 8.6 STATISTICS 149
- 9 MAINTENANCE 150
- 10 TROUBLESHOOTING 151
- 11 TECHNICAL FEATURES 154
- TECHNICAL FEATURES 155
- GLOSSARY 156
- UNI EN ISO 14001 160
Související produkty a manuály pro Čtečky čárových kódů Datalogic QLM500
(30 stránky)
(2 stránky)
Čtečky čárových kódů Datalogic QLM700 Instalační manuál
(120 stránky)
(120 stránky)
(20 stránky)
(2 stránky)
Čtečky čárových kódů Datalogic GryphonD432 Specifikace
(160 stránky)
(160 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.177 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce