Datalogic DX8200A-3010 Instalační manuál stáhnout pdf (Strana 104)

DX8200A REFERENCE MANUAL

To run each instruction press the Next button. The procedure repeats the steps asking to

change the PCT-8000 X position (i.e. always before the PS Line (reference point) and

parallel to a conveyor edge but changing to the left-hand edge and/or to the center of the

conveyor), until the procedure terminates. At the end of the procedure, only the Stop

button is active. Typically 3 passes are necessary.

1 2 ... 99 100 101 102 103 104 105 106 107 108 109 ... 138 139

Reference Manual 1
CONTENTS 3
REFERENCES 6
COMPLIANCE 7
POWER SUPPLY 8
CE COMPLIANCE 9
FCC COMPLIANCE 9
GENERAL VIEW 10
GUIDE TO INSTALLATION 13
1 INTRODUCTION 17
DX8200A - 3 X Y Z 19
1.5 KEYPAD AND DISPLAY 20
1.5.1 Internal Net 20
1.5.2 Test Mode 21
1.5.3 PackTrack (Auto) 21
USING SCANNER MENU 22
1.6.3 Auto PackTrack Setup 24
INTRODUCTION 25
1.7 ACCESSORIES 27
Fieldbus) 28
2 INSTALLATION 29
2.2 MECHANICAL MOUNTING 30
2.2.1 Mounting the Scanner 30
INSTALLATION 31
CBX ELECTRICAL CONNECTIONS 33
3.1 POWER SUPPLY 34
3.2 MAIN SERIAL INTERFACE 35
Function 36
Multidrop Cable 39
Reference 40
USER INTERFACE 40
MEP-593 PH-1 Photocell (PNP) 42
OEK-1 Encoder (PNP) 43
In put De vi ce (Enc oder) 43
9-pin male connector 48
25-pin male connector 48
4.1 POWER SUPPLY 50
4.2 MAIN SERIAL INTERFACE 51
4.2.1 RS232 Interface 52
4.3 AUXILIARY INTERFACE 56
4.4 INPUTS 56
EXTERNAL TRIGGER/ENCODER 57
4.4.1 Code Verifier 59
4.5 OUTPUTS 59
DX8200A USER INTERFACE 60
4.6 USER INTERFACE 61
5 LONWORKS CONNECTIONS 62
5.1 NETWORK TERMINATION 63
5.2 LONWORKS INTERFACE 64
LONWORKS CONNECTIONS 65
6 FIELDBUS CONNECTIONS 66
FIELDBUS CONNECTIONS 67
6.3 DEVICENET INTERFACE 69
6.4 PROFIBUS INTERFACE 70
7 TYPICAL LAYOUTS 71
TYPICAL LAYOUTS 73
Minimum Distance 75
7.1.3 Redundant System 76
7.1.4 Multidata Network 78
7.1.5 Fieldbus Networks 79
8 SOFTWARE CONFIGURATION 81
Test Operating Mode 82
On Line Operating Mode 83
Automatic Operating Mode 83
Net-Autoset 86
Express Network Setup 86
Network Wizard 87
SOFTWARE CONFIGURATION 89
8.4 PARAMETER DEFAULT VALUES 92
9 READING FEATURES 97
9.2 PACKTRACK™ 98
PackTrack™ Reference System 99
DX8200A REFERENCE MANUAL 100
READING FEATURES 101
Auto PackTrack Setup 103
Auto PackTrack Report 106
Scanner Direction 108
PS Offset 109
9.3 PERFORMANCE 112
9.3.1 Reading Conditions 113
9.4 READING DIAGRAMS 115
10 MAINTENANCE 119
11 TROUBLESHOOTING 121
12 TECHNICAL FEATURES 124
TECHNICAL FEATURES 125
A ALTERNATIVE LAYOUTS 126
Fieldbus 127
Network 127
PASS THROUGH 129
RS232 MASTER/SLAVE 130
MULTIPLEXER 132
GLOSSARY 133
DECLARATION OF CONFORMITY 138

Komentáře k této Příručce

Žádné komentáře

Datalogic DX8200A-3010 Instalační manuál Strana 104

Komentáře k této Příručce

Související produkty a manuály pro Čtečky čárových kódů Datalogic DX8200A-3010