Datalogic POWERSCAN PBT7100 guide Specifikace Strana 326
- Strana / 352
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
316 PowerScan® PBT7100 Cordless
BT LED Indications
LED Indication Behavior
Applies to:
Base
Station
Reader
Linking in progress Yellow LED blinks at 2 Hz YES YES
Low battery
Green LED blinks 10 times after either of the following events occur:
-After every 10th trigger pull.
-After 30 seconds of idle time.
NOTE: Low battery LED indication coincides with the low battery
beep.
NO YES
Disconnected LEDs off YES YES
Unlinked LEDs off YES YES
BT transmission in progress Flash yellow LED at 50 Hz while transmitting. YES YES
Paging Yellow LED blinks at the same rate as the paging beep (1 hz) YES YES
BT Reader FRU indication See the topic Error Codes on page 317. NO YES
BT Base Station FRU indi-
cation
See the topic Error Codes on page 317. YES NO
Disabled indication
Green LED blinks once a
second while disabled
NO YES
Battery charge in progress
Green LED blinks once a
second while charging
YES NO
Battery charge complete
Green LED stays ON when charge is complete and reader is seated
in the Base Station.
YES NO
Battery charge error
Yellow LED blinks 550mS on/1500mS off when there is a charge
error and reader is seated in the Base Station.
YES NO
- PowerScan 1
- PBT7100 Cordless 1
- Product Reference Guide 1
- Table of Contents 3
- 2PowerScan 4
- 4PowerScan 6
- 6PowerScan 8
- 8PowerScan 10
- PD7100 Corded 10
- Chapter 1 11
- Introduction 11
- Manual Conventions 12
- References 12
- Technical Support 13
- 4 PowerScan® PBT7100 Cordless 14
- Chapter 2 15
- Getting Started 15
- Connect the Base Station 16
- Figure 3) on the Base Sta 17
- Base Station 18
- Paging Feature 19
- Programming 19
- Configure Other Features 20
- Chapter 3 21
- Interfaces 21
- Select RS-232 OPOS 22
- Select KBD-IBM-M 24
- Global Interface Features 25
- USB Suspend Mode 26
- Chapter 4 27
- General Features 27
- Label Gone Timeout 29
- Label Gone Timeout — cont 30
- Sleep Mode Timeout 31
- LED and Beeper Indicators 33
- Good Read: When to Indicate 34
- Good Read Beep Type 35
- Good Read Beep Frequency 36
- Good Read Beep Length 36
- Good Read Beep Volume 38
- Good Read LED Duration 39
- 2 seconds 40
- Scanning Features 41
- Scan Mode — continued 42
- Stand Mode Triggered Timeout 43
- Scanning Active Time 45
- Scanning Active Time — cont 46
- Flash On Time 47
- Flash On Time — cont 48
- Flash Off Time 49
- Flash Off Time — cont 50
- Stand Mode Sensitivity 51
- Laser Pointer Control 52
- Laser Pointer Period 53
- Laser Pointer Period — cont 54
- Green Spot Duration 55
- Chapter 5 57
- RS-232 ONLY Interface 57
- Baud Rate — continued 58
- Data Bits 59
- Stop Bits 60
- Handshaking Control 62
- Chapter 6 63
- RS-232/USB-Com Interfaces 63
- Intercharacter Delay 64
- Intercharacter Delay — cont 65
- Beep On ASCII BEL 66
- Beep On Not on File 66
- ACK NAK Options 67
- ACK Character 68
- ACK Character — cont 69
- NAK Character 70
- NAK Character — cont 71
- ACK NAK Timeout Value 72
- ACK NAK Timeout Value — cont 73
- ACK NAK Retry Count 74
- ACK NAK Retry Count — cont 75
- ACK NAK Error Handling 76
- Indicate Transmission Failure 77
- Disable Character 78
- Disable Character — cont 79
- Enable Character 80
- Enable Character — cont 81
- Chapter 7 83
- Keyboard Interface 83
- Country Mode 84
- Country Mode — continued 85
- Caps Lock State 87
- Send Control Characters 88
- Wedge Quiet Interval 89
- Wedge Quiet Interval — cont 90
- Intercode Delay 93
- Intercode Delay — cont 94
- USB Keyboard Speed 95
- Chapter 8 97
- USB-OEM Interface 97
- USB-OEM Device Usage 98
- Chapter 9 99
- 46xx Number of Host Resets 100
- 101
- ENTER/EXIT PROGRAMMING MODE 102
- IBM 46XX Interface 104
- Chapter 10 105
- Data Editing 105
- Please Keep In Mind 106
- Global Prefix/Suffix 106
- No Global Prefix 107
- Global Suffix = 0x0D (CR) 107
- Global AIM ID 108
- Global AIM ID — continued 109
- GS1-128 AIM ID 110
- Label ID 111
- Label ID — continued 114
- Case Conversion 122
- Character Conversion 123
- Chapter 11 125
- Symbologies 125
- Coupon Control 126
- UPC-A Enable/Disable 127
- UPC-A — cont 128
- UPC-E Enable/Disable 130
- UPC-E — cont 131
- GTIN Formatting 134
- EAN 13 Enable/Disable 135
- EAN 13 — cont 136
- EAN-13 ISBN Conversion 137
- EAN 8 Enable/Disable 139
- EAN 8 — cont 140
- UPC/EAN Global Settings 142
- UPC/EAN Correlation 144
- UPC/EAN Reconstruction 144
- UPC/EAN Price Weight Check 145
- UPC-A Minimum Reads 146
- Optional Add-ons 147
- Add-Ons — cont 148
- GS1 DataBar Omnidirectional 158
- GS1 DataBar Expanded 160
- GS1 DataBar Expanded — cont 161
- GS1 DataBar Limited 167
- GS1 DataBar Limited — cont 168
- Code 39 Enable/Disable 169
- Code 39 — cont 170
- Code 39 Stitching 185
- Code 32 Enable/Disable 186
- Code 32 — cont 187
- Code 128 188
- Code 128 — cont 189
- GS1-128 Enable 202
- Interleaved 2 of 5 (I 2 of 5) 203
- I 2 of 5 Minimum Reads 206
- I 2 of 5 Decoding Level 207
- I 2 of 5 Length Control 209
- I 2 of 5 Set Length 1 210
- 06 = Length 1 is 6 Characters 211
- I 2 of 5 Set Length 2 212
- I 2 of 5 Set Length 2 — cont 213
- I 2 of 5 Stitching 215
- Datalogic 2 of 5 216
- Datalogic 2 of 5 — cont 217
- Codabar Enable/Disable 228
- Codabar — cont 229
- Codabar Stitching 245
- Code 11 Enable/Disable 246
- Code 11 — cont 247
- Code 11 Decoding Level 257
- Code 11 Stitching 260
- Standard 2 of 5 261
- Standard 2 of 5 — cont 262
- Standard 2 of 5 Stitching 270
- ISBT 128 271
- ISBT 128 — cont 272
- Code 4 Enable/Disable 273
- Code 4 — cont 274
- Code 5 Enable/Disable 275
- Code 5 — cont 276
- Code 4 and 5 Decoding Level 277
- Follett 2 of 5 280
- Chapter 12 283
- BT Features 283
- BT Beeper Features 284
- Beep Frequency 285
- Beep Duration 286
- Beep Duration — cont 287
- Beep Volume 288
- BT Base Station Beep 289
- Disconnect Beep 289
- BT Leash Alarm 290
- BT Leash Alarm — cont 291
- Flash Update 292
- Configuration Update 293
- Configuration Update — cont 294
- Battery Charge Mode 295
- Powerdown Timeout 296
- Powerdown Timeout — continued 297
- BT Poll Rate 298
- BT Poll Rate — cont 299
- Batch Features 300
- Batch Features — cont 301
- BT Security Features 301
- BT Pin Code — cont 303
- BT Security Mode 304
- BT SPP Mode 305
- BT Address Stamping 306
- 00 = No Delimiter Character 308
- Appendix A 309
- Standard Cable Pinouts 312
- Appendix B 313
- DataBar Omnidirectional 316
- DataBar Expanded 317
- DataBar Limited 317
- UCC-EAN 128 318
- Interleaved 2 of 5 318
- Appendix C 323
- BT Beeper Indications 325
- BT LED Indications 326
- Error Codes 327
- Appendix D 329
- 00246897634 330
- 7554628485 330
- 74759330108 330
- DataBar (RSS) 331
- Appendix E 333
- Appendix F 337
- Product Reference Guide 328 338
- Product Reference Guide 329 339
- Product Reference Guide 330 340
- Product Reference Guide 331 341
- Digital Interface 342
- Digital Interface — cont 343
- IBM31xx 102-key 344
- IBM31xx 102-key — cont 345
- Product Reference Guide 336 346
- IBM XT — cont 347
- Product Reference Guide 339 349
- ASCII Chart 351
Související produkty a manuály pro Čtečky čárových kódů Datalogic POWERSCAN PBT7100 guide
(32 stránky)
Čtečky čárových kódů Datalogic QLM500 Instalační manuál
(119 stránky)
(119 stránky)
(2 stránky)
Čtečky čárových kódů Datalogic MAGELLAN 8400 Specifikace
(544 stránky)
(544 stránky)
Čtečky čárových kódů Datalogic Dragon D131 Specifikace
(210 stránky)
(210 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce